WPA NBEMS/FLDIGI
Operations and Proceedures

MT63 - Olivia - DominoEX

MT63 VHF/UHF FM ops - 2K Long Interleave

 Instructions for FM 6m/2m/70cm ops:

### SETUP ###

1) Go to Configure/Modems and click the MT63 tab.
2) Click 64 bit interleave long, save configuration, then close (on vs 3.03 this setting is now saved after restarts of the program).
3) Go to Op Mode/MT63, arrow over and click on MT63 - 2000.

### TUNING ###

1) Tune transceiver to desired FM frequency (make sure all DSP, compression and noise blanker settings are disabled and stations operating under weak signal conditions should open the squelch on the transceiver).
2) All stations should always center on 1500 Hz on the waterfall (MT63 always uses a bottom freq on 500 Hz on transmit. When you initialize MT63, the waterfall tx will be set to this default).
3) Transmit and receive some text to make sure all stations are decoding properly. Assuming that all soundcards are properly calibrated, no tuning should be necessary.

MT63 HF USB ops - 1K/Long Interleave

(recommended USB frequencies: 3.590, 7.090, 14.109):

### SETUP ###

1) Go to Configure/Modems and click the MT63 tab.
2) Click 64 bit interleave long, save configuration, then close (on vs 3.03 this setting is now saved after restarts of the program).
3) Go to Op Mode/MT63, arrow over and click on MT63 - 1000.

### TUNING ###

1) Tune transceiver to desired HF frequency (always us USB and make sure all DSP, compression and noise blanker settings are disabled).
2) All stations should always center on 1000 Hz on the waterfall (MT63 always uses a bottom freq on 500 Hz on transmit. When you initialize MT63, the waterfall tx will be set to this default).
3) Click tune button in the upper right corner of the program and let it transmit for about 10 seconds. Click the tune button again to go back into receive.
4) RX stations center on the received 1000 Hz tone by tuning the receiver VFO.
5) Transmit and receive some text to make sure all stations are tuned and decoding properly.

Olivia HF USB ops - 500Hz/16 Tones

(recommended USB frequencies: 3.584, 7.074, 14.074):

### SETUP ###

1) Go to Op Mode, left click, arrow over Olivia, arrow over to 16/500 and left click.

### TUNING ###

1) Tune transceiver to desired HF frequency (always us USB and make sure all DSP, compression and noise blanker settings are disabled).
2) All stations should always center on 1000 Hz on the waterfall.
3) Click tune button in the upper right corner of the program and let it transmit for about 10 seconds. Click the tune button again to go back into receive.
4) RX stations center on the received 1000 Hz tone by tuning the receiver VFO.
5) Transmit and receive some text to make sure all stations are tuned and decoding properly.

Domino HF USB ops - DominoEX11(FEC)

(recommended USB frequencies: 3.583, 7.073, 14.073):

### SETUP ###

1) Left click on Configure, left click on Modems, left click the Dom tab.
2) Type in your secondary text (i.e. call sign, tactical call, station location), left click both check boxes for Filter On and FEC, then left click save config, then left click close.
3) Go to Op Mode, left click, arrow to DominoEX, arrow over to DominoEX 11 and left click.

### TUNING ###

1) Tune transceiver to desired HF frequency (always us USB and make sure all DSP, compression and noise blanker settings are disabled).
2) All stations should always center on 1000 Hz on the waterfall.
3) Click tune button in the upper right corner of the program and let it transmit for about 10 seconds. Click the tune button again to go back into receive.
4) RX stations center on the received 1000 Hz tone by tuning the receiver VFO.
5) Transmit and receive some text to make sure all stations are tuned and decoding properly.

Back to WPA NBEMS/FLIDIG Page